Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
*********** Setup Hostname *************
Router(config)#hostname LAB_A
*********** Start Setup Serial 0/0 Interface with DCE connection *************
LAB_A(config)#interface Serial 0/0
LAB_A(config-if)#ip addr 10.2.2.1 255.255.255.0
LAB_A(config-if)#clockrate 64000
LAB_A(config-if)#no shutdown
LAB_A(config-if)#
00:08:29: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
00:08:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
LAB_A(config-if)#exit
LAB_A(config)#exit
LAB_A#
*********** End Setup Serial 0/0 Interface with DCE connection *************
*********** Check Interface *************
LAB_A#show interfaces summary
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Hence Details of subinterface are not shown
*********** Start Setup Fast Ethernet l 0/0 Interface *************
LAB_A#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
LAB_A(config)#interface fastethernet 0/0
LAB_A(config-if)#ip addr 10.1.1.1 255.255.255.0
LAB_A(config-if)#no shutdown
LAB_A(config-if)#
00:16:14: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
LAB_A(config-if)#exit
LAB_A(config)#exit
LAB_A#
*********** Check Interface *************
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
NOTE:No separate counters are maintained for subinterfaces
Hence Details of subinterface are not shown
**********************************************************************
FastEthernet0/0 did Not UP yet because of Another Router did Setup yet
**********************************************************************
*********** Check Interface fast Ethernet 0/0 Detail *************
LAB_A#sh int fast 0/0
FastEthernet0/0 is up, line protocol is down
Hardware is AmdFE, address is 000d.28ef.bac0 (bia 000d.28ef.bac0)
Internet address is 10.1.1.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
**********************************************************************
Let setup FastEthernet0/1 at LAB_B router
**********************************************************************
LAB_B(config)#int fast 0/1
LAB_B(config-if)#ip addr 10.1.1.2 255.255.255.0
LAB_B(config-if)#no shutdown
LAB_B(config-if)#
00:29:54: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
00:29:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
LAB_B(config-if)#
*********** End Of setup FastEthernet0/1 At LAB_B router *************
LAB_A#sh int sum
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count